2. OA equipment. PC/PCF. PC/PCF s Features. (Unit: mm) s Applications. (Ta= 25˚C). Creepage distance. Space distance. PC PCF. SHARP PC | Optocoupler; THT; Channels:1; Out: transistor; 5kV; DIP4 – This product is available in Transfer Multisort Elektronik. Check out our wide range of . PC Sharp Microelectronics Transistor Output Optocouplers Non RoHS, use: PCJF datasheet, inventory, & pricing.
|Published (Last):||9 December 2007|
|PDF File Size:||2.8 Mb|
|ePub File Size:||11.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
Please correct pc123 pin numbers in image. If you don’t want pc123 buy a suitable optocoupler like the lc123, 6N, or H11L1, pc123 could try to use additional circuitry to prevent the phototransistor from saturating and to amplify its signal:. To do that, I need an optocoupler, that secures the internal pc123 from damage.
How to test an optocoupler – AntiMath
In the datasheet example, a 10V DC is connected at the output, so pc123 one can check the variation in voltage with a voltmeter or an oscilloscope. I have a PC optocoupler by Sharp lying around, so I’d like to use it in the pc123. The problem is, that I’m not quite sure if this optocoupler can be used for this circuit. Leave a Pc123 Cancel reply Your email address pc123 not be published.
Mihai on July 19, at 3: Here is the web site. This is the schematic as shown by the MIDI specification: Mihai on Pc123 27, at Muhammad Akhlaq on May 30, at 9: Questions Tags Users Badges Unanswered.
For response time pc123 frequency response data, check the datasheet.
Pls let me pc123. Mihai on July 16, at 5: Your email pc123 will not be published.
Pc123 alcohol never solved anything, but neither did water oc123 milk. Pc123 have two circuits. If the input is at 2V DC, then the output resistance should be around — ohms.
If you get a value either way or no pc123 at all, then certainly there is pc123 problem with the LED, and you pc123 find another pc123. This site uses Akismet to reduce spam. Mihai pc132 November 20, at 1: Better check the datasheet for a test circuit. Post as a guest Name. Thank you for the information.
So when current flows through the LED, the triac is triggered and it pc123 both ways until the main current drops below a certain level. I pc123 analog ohmmeter with 2 internal batteries, 3V to turn on LED pins 1 and 2and digital V-metar on diode tester pc123 on transistor side. In my example an ohmmeter is connected at the output, in order to see the change in resistance.
For the pc123 pins 4 pc123 6pc123 no voltage applied to the LED pins 1, 2check with an ohmmeter the resistance pc123 pins 4 and 6, it should be high open circuit or at least greater than 1 megohm both ways, and this resistance should go down lower than ohms when voltage is applied to the LED, and should pc123 low even if the voltage is no longer present on the LED.
Hi, oc123 a stupid pc123 Viliam pc123 September 7, at 1: You helped me understand how to use a tester on a optocoupler Thanks. I like the way you explain things. However, this is nothing I would recommend you rely pc123. The LED is basically a diode, and it should pc123 conduct both ways not get values on the meter both ways.
However, there might be problems pc123 the other parameters of this optocoupler.
Hi, First of all thanks for sharing such an pc123 information. The MIDI specification calls for a high-speed optocoupler.